Part:304X640
Cable Prep offers this high performance SCT-860QR stripping and coring tool. Featuring a 1-Piece design with 3-function blade, it works on 0.860 Quantum Reach CommScope cables. Tool strips, and bevels the outer conductor and cores the dielectric in 1 easy step. Features a one-piece, 3-function blade for perfectly aligned cutting edges, a beveled outer conductor edge that eliminates o-ring damage, a lightweight plastic body and can be operated manually or with a 3/8" power drill.
304X640Cable Prep SCT-860QR Stripping, Coring Tool for Commscope, Quantum Reach QR 0.860" Coax Cable
304X512Cable Prep RSCT-860QR Stripping, Coring Tool With Ratchet Handle, for Quantum Reach QR 0.860" Coax Cable
304X672Cable Prep SC-860QR, 1EA REPLACEMENT BLADE KIT
Note: See Replacement Blade Info Below
SCT-QR stripping/coring tools strip back and bevel the outer conductor,
core the dielectric, and strip back the outer jacket
on CommScope Quantum Reach (QR) cables.
THE SCT-QR ADVANTAGE:
- Perform three functions at once
- Feature non-clogging stops
- Core out-of-round cable
- Prevent O-ring damage
- Operate manually or with a drill
- Include attached jacket-stripping tool
APPLICATIONS
SCT-QR stripping/coring tools work on 0.320" through1.125" CommScope® Quantum Reach® (QR) cables.
Note that, because the jacket must be stripped aftercoring, SCT tools for QR applications include a special,
integrated jacket stripper made especially for this purpose.
SPECIALFEATURES
ThreeFunctions in One Operation
SCT-QR tools speed connectorization because they strip back and bevelthe outer conductor and core the dielectric in one smooth operation.
Non-cloggingStops
There is a non-clogging internal stop on every SCT-QR tool that isfactory-set to the required dimension for the cable.
PatentedStripping/Coring Blades
The bevel on the coring edge ofthe blade self-aligns on the center conductor, which enables an SCT-QRtool to core cable
even when it is out-of-round. Made of tool steelthat is heat treated to full hardness, the blade bevels the outerconductor,
thereby eliminating O-ring damage and minimizing watermigration.
Manual orDrill Operation
SCT tools can be ordered with a standardergonomic handle or a Cable Prep brand RTH ratchet T-handle. Eitherhandle can be removed for operation with a 3/8-inch variable speeddrill.
AttachedJacket Stripping Tool
Because the jacket on QR cable mustbe stripped after the coring operation, each SCT-QR stripping/coringtool (labeled SCT-QR-A) comes with a special jacket stripping tool(labeled SCT-QR-B). The two pieces are threaded, so they can beassembled and stored as one unit, which protects the insides of theparts from damage. The jacket stripper is designed with a patentedmandrel pin that supports the soft aluminum outer conductor and keepsit from being damaged during the jacket stripping operation.
REPLACEMENTBLADE KIT
¼” exposed braid
.250” exposed center conductor
NOTE:The notched blade in the cartridge eliminates the risk of scoringthe center conductor and cuts through the jacket, braid, foil anddielectric
leaving the center conductor exposed. The shallow blade cutsthrough only the jacket of the cables.
REPLACINGCARTRIDGES
The purpose of this tool is to provide consistent quality, while savingtime. For this tool to perform correctly,
the cartridge must bereplaced when the blades are dull. Depending on the cable you areusing, the number of cuts per blade cartridge varies.
For bestperformance the blade should be kept free of any debris or floodantresidue.
If you see that the cut is not as clean, the braid isstraggled, or the tool takes more revolutions to cut — REPLACE THECARTRIDGE IMMEDIATELY.
HOW TOREPLACE THE CARTRIDGE
While holding the tool, depress the lever and grasp the cartridge onboth sides.
Then pull cartridge straight down and out.
Reverse thisprocess for cartridge installation and then snap the cartridge inplace.
Move fingers away from cartridge and let go of lever.
WARRANTY